How To Install RAM?

Author:

Category:

Learning how to install RAM is a great way to speed up your computer. Almost all modern computers are loaded with a range of different components. RAM is one of the most vital components of your PC. without RAM your computer cannot run or perform any tasks. In today’s post, I will show you how to install RAM on a laptop and PC. It is very important to keep your computer well-updated with the latest software. Installing new RAM can improve the performance of your computer. You can keep on reading further to know more about how to install RAM in detail.

How To Install RAM?

Follow these steps to learn how to install RAM.

  1. First, purchase the RAM that’s compatible with your device.
  2. Once you have your RAM, shut down your computer.
  3. Unplug your computer’s power plug and other connected devices such as monitors, keyboards, and mice.
  4. Now, open your computer case using a screwdriver.
  5. Make sure that you do not have static build-up on your body.
  6. You can use an antistatic wrist strap or ground yourself before starting.
  7. Then, locate your device’s RAM slots.
  8. Press the clamps downward on either side of the slot to remove old RAM.
  9. Gently lift the RAM straight out of the motherboard with little to no effort.
  10. Now, remove the new RAM from the shielding packaging.
  11. You can grip it from the sides to avoid touching the contacts on the bottom.
  12. Carefully insert the RAM into the RAM slot.
  13. Then, apply equal pressure onto the stick until the clamps on the side click.
  14. Once you hear the click, the RAM is locked in.
  15. After inserting your RAM, close your computer case and screw it back.
  16. Power on your computer to verify that the RAM has been installed correctly.
  17. Then, press the Windows key + Pause/Break simultaneously.
  18. This will open up the System Properties.
  19. Go to the System section to view your RAM.

You can follow the same procedure if you want to know how to install 16GB RAM. If you are unable to find RAM slots, you can look for narrow slots about 4.5 inches long with tabs on either end. Here, you’ll see one of the slots already has a stick of RAM in it.

You can keep on reading further to know more about how to install RAM in the motherboard.

Install RAM On Laptop

The process of installing new RAM on a laptop is a bit different from the previous method. You can follow these steps to learn how to install RAM in a laptop.

  1. Before you start, find which type of RAM is required for your laptop.
  2. Once you find the right RAM, shut down your laptop.
  3. Remove any external cables that are attached.
  4. You can even press and hold the power button for 5 seconds to discharge residual power.
  5. Now, place your laptop upside down on a flat surface.
  6. Make sure that you do not have static build-up on your body.
  7. You can use an antistatic wrist strap or ground yourself before starting.
  8. Then, locate your device’s RAM slots.
  9. Now, check how many RAM slots your laptop have.
  10. Determine if your RAM needs to be installed in pairs or singly.
  11. Press the clamps downward on either side of the slot to remove old RAM.
  12. Gently lift the RAM straight out of the motherboard with little to no effort.
  13. Now, remove the new RAM from the shielding packaging.
  14. You can grip it from the sides to avoid touching the contacts on the bottom.
  15. Carefully insert the RAM into the RAM slot.
  16. Then, apply equal pressure onto the stick until the clamps on the side click.
  17. Once you hear the click, the RAM is locked in.
  18. Now, close your laptop and power it back on.

After a while, your laptop should boot up normally and automatically detect the RAM. You can follow the same procedure if you want to know how to install RAM DDR4 and DDR3 on a PC.

Install RAM On iMac

Installing TAM on an iMac is also an easy task. Follow these steps to learn how to install RAM on the iMac.

  1. First, visit https://support.apple.com/en-us/HT201191 to find out what type of RAM your iMac will need.
  2. Once you get to know the right model, purchase the RAM offline or online at Apple Stores.
  3. Shut down your iMac and disconnect all power cords that are connected to your iMac.
  4. Place your iMac on a flat surface laying on a clean soft towel.
  5. Then, press the gray button above the power port to open your iMac’s memory access door.
  6. Remove the old RAM and replace it with the new RAM.
  7. Once you are done, close the memory access door and turn on your iMac.

You might need a head screwdriver to open the memory access door.

Tips To Consider While Choosing Your RAM Upgrade

By far, I hope you have understood how to install new RAM in the motherboard. There are a few factors you have to consider when you are purchasing a component like these.

  • While installing a new RAM, consider how much RAM your PC/laptop needs. For lightweight usage, 4GB of RAM is enough and for multitasking, 8GB of RAM is good. 
  • You also have to figure out which speed your motherboard can handle inside its manual.
  • Check the DIMM slot availability as most modern motherboards have multiple RAM slots. Some will have four, two, or eight plus RAM slots.

Now, you must be wondering what to do after installing new RAM. Once you install the RAM, you simply have to boot up the computer. You can also check whether your upgrade worked by launching the Control Panel >> System and Security >> System. Here, you can see all the details.

Get to know more similar topics like these on Techkorr

FAQ

Can You Just Install New RAM?

Is it possible to just add a new RAM to the existing RAM in order to boost the memory of my desktop PC? Yes, but if you do, you will have to use the exact type of memory that came with your computer. You also have to have enough RAM slots.

Which RAM Slots To Fill First?

Fill slot 0 (or 1) first, then the other slots sequentially as you add modules. If you are installing memory in a dual-channel memory motherboard, install memory modules in pairs, filling the lowest numbered slots first.

How Do I Know If I Put RAM In Correctly?

Go to ‘Windows Memory Diagnostic’. The computer will restart itself and check the RAM module for errors. After the check, you can see a report on your screen about the status of your RAM. If the check has found a problem, the report will tell you what to do.

Do I Need To Do Anything Before Installing New RAM?

Ground yourself! Touch an unpainted metal surface – this is an extra safeguard that protects your computer memory and components from static damage during the installation process. Static electricity can damage the components in your system.

Conclusion

In the above post, I’ve explained how to install RAM in a PC step-by-step in detail. Having enough RAM is vital for smooth processing. RAM is available in a variety of models, sizes, and speeds. Simply release RAM modules by pressing down on the clips and replacing them with new RAM modules. Make sure you reassemble your PC/laptop and plug all accessories back in. You can check your motherboard or computer’s documentation to know which RAM is compatible with your hardware. Once you understand how to install RAM, you can easily boost your PC’s speed.

Read More

Related Articles